We FIX Smeg

Smeg Dishwasher Repair

Drainage, leaks, heating element, control board, door latch — we repair every Smeg dishwasher fault. Same-day service across the GTA.

1. E1 – Water Supply Error – The dishwasher is not filling with water. Check the water inlet valve, hose, or filter for blockages.
2. E2 – Drainage Error – The dishwasher is not draining properly. Check the drain hose, pump, or filter for blockages.
3. E3 – Heating Error – The dishwasher is not heating water correctly. This could be due to a malfunctioning heating element or temperature sensor.
4. E4 – Overflow Error – There is an issue with the water level, causing the dishwasher to overflow. Check for a faulty float switch or blocked drain.
5. E5 – Door Lock Error – The door is not properly locked, preventing the dishwasher from starting or completing a cycle.
6. E6 – Communication Error – A problem with the dishwasher’s electronic control system or wiring.
7. E7 – Motor Error – There’s an issue with the dishwasher motor, possibly preventing it from starting or completing the cycle.
8. E8 – Water Temperature Error – The water is not reaching the correct temperature during the wash cycle.
9. E9 – Drying Error – The dishwasher is unable to dry the dishes properly, which could be due to a malfunctioning heating element.

Need Smeg dishwasher repair today? Call +1-647-834-4646.

Smeg Washing Machine Repair

Drainage faults, motor errors, sensor failures, door-lock issues — our techs repair them all on Smeg top-load and front-load washers. Same-day service across the GTA.

1. E1 – Water Supply Error – The washing machine is not filling with water. Check the water inlet valve, hose, or filter for blockages.
2. E2 – Drainage Error – The washing machine is not draining properly, possibly due to a clogged pump or drain hose.
3. E3 – Unbalanced Load Error – The load in the washer is unbalanced. Redistribute the clothes to correct this issue.
4. E4 – Overflow Error – The washer is overfilling with water, potentially due to a malfunctioning water level sensor.
5. E5 – Door Lock Error – The door is not properly locked, which prevents the cycle from starting or completing.
6. E6 – Heating Error – The washer cannot heat water to the proper temperature. This may be due to a faulty heating element.
7. E7 – Motor Error – There’s an issue with the motor or drive system, preventing the washer from spinning or agitating.
8. E8 – Electronic Board Error – A malfunction with the washer’s control board or communication between components.
9. E9 – Filling Time Error – The machine is taking too long to fill with water, likely caused by a blocked inlet valve or hose.

Need Smeg washing machine repair today? Call +1-647-834-4646.

Smeg Refrigerator Repair

Compressor faults, defrost-system errors, sensor failures, ice-maker problems — we fix every Smeg fridge issue. Same-day service across the GTA.

1. E1 – Temperature Sensor Error – The refrigerator is not detecting the correct temperature due to a faulty sensor.
2. E2 – Defrosting Error – The refrigerator’s defrost system is malfunctioning. Check the defrost heater, thermostat, or timer.
3. E3 – Compressor Error – There is a problem with the refrigerator’s compressor, possibly preventing it from cooling properly.
4. E4 – Overheating Error – The refrigerator has detected that the internal temperature is too high. This can be caused by blocked vents or a dirty condenser coil.
5. E5 – Power Failure Error – The refrigerator has experienced a power failure, potentially due to a surge or a malfunction in the power supply.
6. E6 – High Temperature in Freezer – The freezer temperature is too high, which may indicate a blocked vent or problem with the compressor.
7. E7 – Low Temperature Error – The refrigerator temperature is too low and not reaching the set point.

Need Smeg refrigerator repair today? Call +1-647-834-4646.

Smeg Oven Repair

Burner ignition, sensor faults, control board errors, door-seal issues — we fix every Smeg oven and stove issue. TSSA-certified for gas, same-day across the GTA.

1. F1 – Control Board Error – The oven control board has malfunctioned and is unable to communicate with the system properly.
2. F2 – Temperature Sensor Error – The oven’s temperature sensor is faulty or disconnected.
3. F3 – Heating Element Error – A problem with one of the heating elements, either the top or bottom, is preventing the oven from heating correctly.
4. F4 – Fan Error – The oven fan is malfunctioning, which may be due to a faulty fan motor or control.
5. F5 – Door Lock Error – The oven door is stuck in the locked position or not locking properly. This could be an issue with the door lock mechanism or control.
6. F6 – Relay Error – A malfunction in the relay switch is preventing the oven from reaching or maintaining the desired temperature.
7. F7 – Temperature Too High Error – The oven temperature is exceeding the maximum set point, indicating a potential overheating issue or sensor malfunction.
8. F8 – Communication Error – A communication breakdown between components in the oven, such as between the control board and sensor.

Need Smeg oven repair today? Call +1-647-834-4646.

Smeg Microwave Repair

Magnetron, control panel, door interlock, turntable motor — we repair Smeg built-in and over-range microwaves. Same-day service across the GTA.

1. E1 – Keypad Error – A malfunction with the microwave keypad is preventing the appliance from responding to user input.
2. E2 – Temperature Sensor Error – The microwave’s temperature sensor is not functioning properly, affecting its operation.
3. E3 – Magnetron Error – The magnetron is malfunctioning or failing to generate microwave energy.
4. E4 – Relay Error – A problem with the microwave’s relay system, which can affect the appliance’s performance.
5. E5 – Control Board Error – The microwave’s control board is faulty, potentially affecting its functionality.

Need Smeg microwave repair today? Call +1-647-834-4646.