Sharp

Sharp Washing Machine Error Codes:

1. E1 – Water Supply Error – The washing machine is not filling with water. This could be caused by a blocked water inlet valve, filter, or hose.
2. E2 – Drainage Error – The washer cannot drain water properly, possibly due to a clogged drain hose or pump.
3. E3 – Unbalanced Load Error – The load in the washing machine is unbalanced and needs to be redistributed for proper operation.
4. E4 – Overflow Error – The washer has detected an overflow of water, which might be due to an issue with the water level sensor.
5. E5 – Door Lock Error – The washer door is not locking properly, preventing the cycle from starting or finishing.
6. E6 – Motor Error – There’s an issue with the washing machine motor, possibly due to a malfunction or connection problem.
7. E7 – Heating Error – The washer cannot heat the water properly, which may indicate a malfunctioning heating element or sensor.

Sharp Refrigerator Error Codes:

1. H1 – High Temperature in Freezer – The freezer temperature is too high. This could be due to a malfunctioning thermostat, blocked vents, or dirty condenser coils.
2. H2 – High Temperature in Refrigerator – The refrigerator is too warm, possibly caused by a blocked air vent or faulty thermostat.
3. E1 – Defrost Sensor Error – There is an issue with the defrost system, which might cause the freezer or refrigerator to freeze over.
4. E2 – Temperature Sensor Error – A temperature sensor in the refrigerator or freezer has malfunctioned.
5. E3 – Compressor Error – There is an issue with the refrigerator’s compressor, which might prevent it from cooling correctly.
6. E4 – Power Failure Error – The refrigerator detected a power failure or electrical interruption.

Sharp Microwave Error Codes:

1. F1 – Microwave Relay Error – There’s an issue with the relay switch inside the microwave, preventing it from operating normally.
2. F2 – Magnetron Error – The magnetron, which generates the microwave energy, is malfunctioning or has failed.
3. F3 – Sensor Error – The microwave’s humidity or temperature sensor is not functioning properly.
4. E1 – Keypad Error – There’s a malfunction with the microwave’s keypad or control panel, which may prevent button presses from being registered.
5. E2 – Internal Communication Error – The microwave’s internal components are not communicating properly, which could involve a circuit or board issue.

Sharp Dishwasher Error Codes:

1. E1 – Water Supply Error – The dishwasher is not filling with water, likely due to a blocked water inlet valve or filter.
2. E2 – Drainage Error – The dishwasher is unable to drain water, possibly due to a clogged pump or drain hose.
3. E3 – Heating Error – The dishwasher is not heating water to the desired temperature. This could be due to a faulty heating element or thermostat.
4. E4 – Overflow Error – The dishwasher has detected water leakage or overflow, possibly from a damaged hose or pump.
5. E5 – Leakage Error – The dishwasher has detected a leak in the system, which could be caused by a damaged seal, hose, or other component.

Sharp Air Conditioner Error Codes:

1. E1 – Indoor Temperature Sensor Error – There is an issue with the temperature sensor inside the air conditioner.
2. E2 – Outdoor Temperature Sensor Error – The outdoor temperature sensor is malfunctioning.
3. E3 – Frozen Coil Error – The evaporator coil is frozen, possibly due to a dirty air filter, low refrigerant, or insufficient airflow.
4. E4 – Communication Error – The indoor and outdoor units are not communicating properly, which may indicate a wiring or control board issue.
5. E5 – Fan Error – The air conditioner fan is not working correctly, which could be due to a faulty motor or blocked vent.

Sharp Oven Error Codes:

1. F1 – Control Board Error – There’s an issue with the oven’s control board, possibly due to a short or malfunction.
2. F2 – Temperature Sensor Error – The oven’s temperature sensor is malfunctioning or disconnected.
3. F3 – Heating Element Error – The oven’s heating element is faulty and is not heating properly.
4. F4 – Relay Error – The oven’s relay or switch is malfunctioning, preventing it from reaching the correct temperature.
5. F5 – Door Lock Error – The oven door is not locking or unlocking properly, preventing self-cleaning or other cycles from completing.